LABOR CHARGES Hourly Rate (65.00/HR) MINIMUM LABOR CHARGE $32.00 CLEANING • Handguns 45.00 • Rifles 50.00 • Shotguns 50.00 FINISH • Hunter Finish 300.00 • Master Oil (Gloss Or Matte) 400.00 • Lacquer (Filled Grain) 275.00 Bluing/Plating • Handguns 200.00 • Rifle/Shotgun 250.00 • Electroless Nickel Handgun 225.00 • Hard Chrome Handguns 250.00 • Electroless o/u Shotgun Reciever 275.00 Auto Install Oversized Long or short 35.00 Jewel Sides of Triggers 40.00 Trigger Job – S/A 70 Series 90.00 Trigger Job - S/A 80 Series 95.00 Trigger Job – D/A & S/A 120.00 Adjust Disconnector 20.00 Grip Safety Install Brown 80.00 Install Wilson, Kings, etc… 80.00 Install Drop –In (No Frame Mod) 15.00 Thumb Safety Extended – Any Make 40.00 Ambidextrous – Any Make 50.00 Custom to Order 65.00 Sights/Slide BoMar Real Low Mount 150.00 BoMar Low Mount w/Pocket 185.00 Drop –In Any Make 30.00 Staked & Soldered Front (Any Make )45.00 Dovetail Front Sight 75.00 Colored Insert Front & Rear 25.00 Night Sight Front & Rear 30.00 Lower Ejection Port 65.00 Tune Extractor 25.00 Tighten Slide 175.00 |
Mag Wells Enlarge Magazine Well (No Add-on Part) 85.00 Enlarge Any Add-On Well 85.00 Custom Made to Order 200.00 Barrels Fit Custom Match Barrel Non Ramped 140.00 Fit Custom Match Barrel –Ramped 185.00 Thread Barrel (No Charge w/CompPurchase)80.00 Weld/Fit Factory Barrel 100.00 Throat & Polish Barrel/Ramp 50.00 Fit Match Target Bushing 75.00 Long Link 20.00 Checkering Front Strap –1911 325.00 Hi Grip Front Strap – 1911 375.00 Front Strap – Para Ord. 425.00 Hi Grip Front Strap-Para Ord. 500.00 Front of Trigger Guard 80.00 Finger Rest Front Trigger Guard 80.00 Mainspring Housing 30.00 Serrate Back of Slide 30.00 (Add 20% For S/S Carry Compensators & Race Guns #1 SV Carry Comp 425.00 • .600 O.L. • One Chamber One Port ½” Long • 2-Pc. Guide rod w/extended spring cap • Re-blue slide and comp #2 SV 100 575.00 • Slide Cut ½” • Three Chamber-threeport-45acp-10mm • Two Chamber-two port-38super • Tapered Cone Design • 6” overall • Front sight of choice, removable, in front or behind ports • Re-blue slide/compensator • 2-pc. Guide rod #3 SV 100 MAGNUM 700.00 • Scoped Use Only • Same as #2 but with higher ports creating more port surface are, thus eliminating more muzzle flip. #1 No Glare Rib 125.00 • Top of slide milled flat and radiused to resemble a rib #2 Lighten Slide 125.00 • Remove metal from slide in unseen areas to promote faster cycling of slide. • STAINLESS STEEL- ADD 50.00 Revolvers Trigger Trigger Stop- Adj. 55.00 Trigger Stop-Non-Adj. 35.00 Smooth Trigger For Combat 40.00 Bob Hammer 45.00 Trigger Job 110.00 Thin Trigger Sides 50.00 Barrel Any Factory Replacement 100.00 Custom Barrel 165.00 Custom Rib Machined Into Barrel 200.00 Custom Barrel Comp. 300.00 Sega Port 220.00 Drill & Tap for Scope-Per Hole 20.00 • Set up 20.00 Custom Barrel Slab Sided 125.00 Sights Custom Barrel – Sights Front 85.00 Colored Insert – Front Sight 30.00 White Outline S&W (P/L) Parts 45.00 White Outline Ruger & Colt (P/L) 45.00 Other Retime Cylinder 125.00 Custom Underlug Made to Order P.O.R. Chamfer Cylinder 65.00 Square Butt To Round 125.00 Re-crown Barrel 75.00 Re-cut Forcing Cone 55.00 Straighten Extractor Rod 50.00 Straighten Crane 80.00 Shim Hammer-Crane-Cylinder (Min) 30.00 Underlug-Per Hole 20.00 Crane Lock-up-Ball/Detent 140.00 Rifle Action/Trigger Smooth Action-Auto/Pump/Lever 150.00 Lapping Bolt 125.00 Trigger Job - Auto or Pump 125.00 Trigger Job Bolt Action 95.00 Non – Adjustable Triggers Match Triggers – Adjustable 80.00 Double Set Triggers 125.00 Shilen Triggers – Match 140.00 Trigger Job – Adjustable Trigger 70.00 Savage Trigger Job 140.00 Barrel Chamber-Thread-Fit Barrel to Action(No Sights) 325.00 Barrel Replaced w/Factory Barrel (Pre Threaded & Chambered) 140.00 Cut Barrel – Re-Crown (No Sights) 100.00 Check Headspace 50.00 Re-Chamber 150.00 Thread Barrel For Recoil Reducer 110.00 Thread Barrel for Recoil Reducer w/sights 130.00 Pull Barrel to Thread Barrel for Recoil Reducer w/sights 200.00 Set Barrel Back 130.00 Military Barrel Replace/Auto 150.00 Straighten 80.00 Sights Set Up For All Drill & Tap 20.00 Drill & Tap 20.00/hole Drill & Tap Military 25.00/hole Dovetail 70.00 Solder Front/Rear 75.00 Install Screw on Front Sights 60.00 Mount Scope & Bore Sight 30.00 Shim Scope or Base 20.00 Bolts Bend w/o Cutting 100.00 Bend w/Cutting 130.00 Mfg. New Bolt Handle 150.00 Jewel Bolt 200.00 Make Firing Pin 100.00 Safety – Beuhler 80.00 Win 70 180.00 Miscellaneous Remove Ruptured Case From Chamber 50.00 Remove Live Round 50.00 Install Swivels 45.00 Stocks Fit/Glass Complete-Float Barrel 240.00 Float Barrel Only –No Glass 65.00 Glass Channel & Lugs-Float Barrel 100.00 Match w/Pillars 225.00 Military Glass Complete 200.00 Paint Synthetic Stock/ Wood Stocks 150.00 Cut Stock for Recoil Pad 20.00 Checker 55.00/Hr. Re-cut Checkering 50.00min. 50.00/Hr. Install Recoil Pad 50.00 Shotguns Action/Trigger Smooth Action (Pump/Auto) 100.00 Trigger Job 120.00 Big Head Safety 25.00 Barrel Open Choke 65.00 Screw In Choke 120.00 External Choke 115.00 Cut Barrel & Crown – Reset Sight Center Bead 65.00 Re- Solder Loose Ribs(w/blueing) 150.00 Sega–Port Barrel(Recoil Reduction) 250.00 Miscellaneous Tighten Hinge Pins on Doubles 175.00 Recoil Reducer/Butt Stock 125.00 Swivels 40.00 Lengthen Forcing Cone 90.00 |
Home > Shop > Pricing/Labor Charges
